ejecting

英 [iˈdʒektɪŋ]

美 [iˈdʒektɪŋ]

v.  驱逐; 逐出; 赶出; 喷出; 喷射; 排出; (飞行员在飞机坠毁前从弹射座椅)弹出
eject的现在分词

柯林斯词典

• VERB 驱逐;把…逐出
  If youejectsomeonefroma place, you force them to leave.
  1. Officials used guard dogs to eject the protesters...
     官员们用警犬驱散抗议人群。
  2. He was ejected from a restaurant.
     他被逐出餐厅。
• VERB 弹出;喷出;射出
  Toejectsomething means to remove it or push it out forcefully.
  1. He aimed his rifle, fired a single shot, then ejected the spent cartridge.
     他用步枪瞄准，射出一枚子弹，然后退出空弹壳。
• VERB （通常指飞行员从即将坠毁的飞机中）弹射出来
  When a pilotejects froman aircraft, he or she leaves the aircraft quickly using an ejector seat, usually because the plane is about to crash.
  1. The pilot ejected from the plane and escaped injury.
     飞行员从飞机中弹出，安然无恙。

双语例句

• The ejecting flying toy also comprises an afterbody form finalizing sheet which is fixed at the center of the rear part of the airfoil.
  弹射飞行玩具还包括机尾定型片，机尾定型片固定在机翼后部中央。
• A control mechanism for a typewriter or other listing device that can automatically control the feeding, spacing, skipping and ejecting of paper or preprinted forms.
  打字机或其它打印设备的控制机构，能自动控制走纸、空格、跳格以及弹出打印纸或表格纸。
• During an attempt at ejecting the CD magazine.
  在试图弹出CD盒期间。
• Based on a double foundation characteristic, two schemes of high pressure ejecting grout plank wall and ballast for preventing piping and soil flow were investigated.
  根据双层地基的特点，分别对复合土工膜堆石堤堤基采用高压喷射灌浆板墙方案和压重防止管涌流土方案的防渗效果及经济性进行了计算比较。
• Type of radioactive disintegration ( see radioactivity) in which some unstable atomic nuclei dissipate excess energy by spontaneously ejecting an alpha particle.
  放射性蜕变的一类，某些不稳定原子核自发射出一个α粒子以耗散过剩能量。
• DESIGN INJECTION MOULD WITH QUADRATIC EJECTING MECHANISM OF SLIDER AND WEDGE DUAL PUSH PLATE The friction is modeled with a modified coulomb friction model.
  滑块斜楔双推板式二次推出机构注塑模的设计模具与板料的接触摩擦采用一个修正的库仑摩擦模型。
• The act of ejecting or the condition of being ejected. Flames jetted out ( of the nozzles).
  喷出喷出的动作或被喷出的状态火焰（从喷嘴中）喷出来了。
• Ejecting and heating performance of the heater at low steam pressure was studied through the experimental method.
  用试验方法研究了该加热器在低进汽压力下的引射性能和加热性能。
• Througn designing three axial slots in internal threaded portion and optimizing nib structure, a design was made on the injection mould with a two-step ejecting mechanism with non-rotating.
  对笔尖内螺纹部分设计三段轴向开槽，优化笔尖结构，设计了二次推出不带旋转机构的自动脱螺纹注塑模。
• Ejecting coefficient decreases while the distance between water nozzle and mixed spout increases.
  在入口水压一定的条件下，喉嘴距较大时引射系数较小；